How do I reset my Maytronics pool cleaner?

Restart the cleaner; press and hold the reset button until the light goes off (approximately 5 – 20 seconds). If light still does not go off, take your Dolphin to your local dealer or call Maytronics Customer Service.

Why is my automatic pool vacuum not moving?

If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.

How long should a pool cleaner run each day?

approximately 8 hours a day
Every pool must turn over at least once a day, so most pool pumps should run approximately 8 hours a day.

Why is my pool creepy crawly not moving?

If Kreepy Krauly is not moving or not pulsating. Check that the main drain and all suction lines are closed, except for the suction line to which Kreepy Krauly is attached (usually a skimmer). Check for debris in the filter or [pump basket]. Check for debris in Kreepy Krauly flapper.

How do you troubleshoot a Maytronics dolphin?

Troubleshooting

1. Check that the power supply cable is plugged properly into the power supply socket. Check power to the socket and reconnect Pool Cleaner.
2. Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box.
3. Turn the power supply off.
4. Unplug the power supply.

How do I get my dolphin pool cleaner to work?

The Maytronics Dolphin Nautilus Robotic Cleaner is self-contained and fully automatic. Just drop it in your pool, turn it on and leave it for about 3 hours.

Why does my pool pump have no suction?

It could be something blocking it, a dirty pool filter, or too much air in the system. If there’s something blocking your pump’s suction, check your filter gauge. If it’s 10psi above the normal reading, clean your filter. This will reduce pressure and reset your pump’s flow.

Is it better to run a pool pump at night or day?

It is best to run your pool’s pump during the day when the sun is out to reduce the risks of algae bloom and because there is generally more debris and contaminants that will enter your pool in the day.

Is it OK to run pool pump 24 hours a day?

A Rule of Thumb Generally running your pool pump for 12-hours a day is a good option. This is based on the assumption that your average pool pump has a turnover rate of about 8 to 12-hours. That means that the total volume of your pool water will filter through your system 2 to 3 times per 24-hour period.

How long should a pool sweep run?

You should allow the vacuum to run until it has cleaned the entire pool, including the bottom and the sides. This averages between two and six hours. The better your pool has been maintained — for example, if you vacuum every week — the less time it takes.

Why is there no suction on my pool vacuum?

Verify that the vacuum hose is firmly inserted into the inlet port at the skimmer; then inspect the hose for cracks or holes. The skimmer filter is dirty. Pull out the filter basket and check for debris that may be interfering with water flow to the pool pump. Air is getting into the pump through the pump cover.

How do I reset my dolphin?

Press and hold “Blue” and “Call” buttons to cold boot the Dolphin. Upon cold boot, when the display returns, type: 1277. A little menu will appear showing the reset options.

Why is my Dolphin pool cleaner not moving?

If you can identify an obstruction you can remove the object and then run your Dolphin again. If the Dolphin starts and continues to operate as per normal the the obstruction was the cause of the robotic pool cleaner not moving.

Can I leave my Dolphin pool cleaner in the pool overnight?

Can you leave the Dolphin in the water? It is safe to leave your Dolphin cleaner in the water when not in use. However, (when adding chemicals to the pool) please remove the Dolphin until the proper chlorine and PH balance are obtained.

How long does it take a pool pump to prime?

Prime the pump at the beginning of each pool season. When you prime the pump, you add water to it and bleed off the air in the lines. Prime your pump anytime your pool sits for 1-2 months.

How do you reset pool pump after power outage?

Close any drain plugs or valves you may have opened during the power outage. Turn the breakers back on and prime the pool pump by adding water to the pot, replace the lid and turn the pool pump on. Ensure your pool pump and filter are working, and then let them run for one hour to begin decontamination.

Should I turn off pool pump when raining?

If your pool pump manufacturer has declared your pump is rain safe, you can leave it on in rainfall. Nevertheless, during a thunderstorm, it is highly recommended that you switch off and unplug your pool pump to prevent any costly and irreversible damages to your pool equipment.

How long does it take for a swimming pool to recover?

Obviously, pools that are days away from becoming a swamp require more time and maintenance than a pool recovering from a rainy day. And swimming pools that require an extensive treatment due to algal blooms are in a class of their own. It can literally take weeks. On average, pool owners use three to five times the normal dosage when shocking.

How do you calculate run time on a pool filter?

Method 1 Calculating Run Time per Day. For example, using a pool volume of 19,149 gallons and a filtration rate of 3,000 gallons per hour: (Pool Volume ÷ Filtration rate) x 2 = Hours to run filter (19,149 ÷ 3000) x 2 = 12.766, or about 12 hours and 45 minutes for a full 2 cycles.

What are the biggest mistakes people make when resetting their pools?

One of the biggest mistakes that people make when they are resetting their pools after a problem is that they don’t remove all of the objects or debris that is between the wall and liner or near the liner.

How long should I Run my pool filter at night?

Although running your filter at night may save you energy, it does nothing to prevent the algae from forming during the day when it’s actually got a chance to, unlike at night. Feel free to safely run your filter 10-12 hours a day. Your pool filter is intended to be run for up to 12 hours a day consistently.