How do I reset my cisco sg200 26?

Configure your laptop’s network interface to be in the 192.168. 1.1/24 network, but avoid the 192.168. 1.254. Now find a small pin (I used the one from the office stepler) and push into the Reset hole of the switch for about 30 seconds.

Where is the password on my cisco router?

0.1 in your Internet browser. Log in with the following information: Username: cusadmin. Password: You can find this password printed on the white sticker on your Shaw Wireless Modem (Cisco), referred to as the S/N (usually a 9-digit number starting with 2xxxxxxxx).

How do I reset my cisco router to factory default?

Reset Router to Default Configuration

1. With the router powered off, connect the power cord to your router, and plug the power cord into your power source.
2. Find the Reset button on the router.
3. Press and hold the Reset button while you power on the router.
4. Release the Reset button after 10 seconds.

How do I reset my cisco switch password?

Find the below steps to recovery password for Cisco 2960.

1. Power off the switch first, then press and hold the mode button while you power on the switch again.
2. To initialize the flash file system, run the command:
3. You can now list the contents of your flash by running.
4. To further boot the switch run the boot command as:

What is the default username and password for Cisco AP?

The default username is Cisco. Step 4 Enter the wireless device password in the Password field and press Enter. The default password is Cisco.

How do I reset my Cisco router to factory settings without a password?

Reset Router Using Reset Button

1. With the router powered off, connect the power cord to your router, and plug the power cord into your power source.
2. Find the Reset button on the router.
3. Press and hold the Reset button while you power on the router.
4. Release the Reset button after 10 seconds.

How do I log into my Cisco router?

Cisco router login:

1. Make sure you’re connected to your network.
2. Open a browser, and go to 192.168. 15.1.
3. Enter the username and password.
4. Default login credentials.
5. Next Up: Speed up your Wi-Fi connection.

How do I reset my Cisco switch password?

How do I Reset my cisco router to factory settings without a password?

How do I log into my cisco router?

How do I reset my 2960 to factory settings?

Reset a Cisco 2960 Switch to Factory Default Settings

1. – Start by connecting your cisco switch via a console cable that will be also connected to the same console.
2. Step 2.- Use the following commands: Router: en. Router#erase startup-config. Router# del flash:vlan.dat.
3. – Reload your cisco switch to complete the restoration.

What is the default IP for Cisco 2960 switch?

10.0.0.1
The switch has a default IP address “10.0. 0.1” and a secondary IP address “10.0. 0.3”.

How do I reset a cisco switch to factory default?

Hold the “mode” button on the front of the switch for 10 seconds. The lights will blink then go solid – the switch completely wipes all configuration and then reboots.

What is the default password for Cisco?

Type “http://192.168.0.1” into a browser of your choice and hit “Enter”.

When you access the device,you should be asked to enter a username and password.

The default user name of your Cisco router is either “admin” or “cisco”.

Once you input this account name and password,you should have no issue setting up your device securely.

How do I Reset my Cisco password?

Account security. Use the security page to change your password,setup multi-factor authentication,add your mobile phone number,and view your certification hash.

Change password. Select “Edit” to begin.

Multi-factor authentication. Multi-factor authentication (MFA) adds another layer of security to your account.

Settings.

How to set user and password on Cisco router?

– Setting router name to R1 – Set privileged mode password to cisco – Set privileged mode secret to cisco – Set console line password to lab – Set auxiliary line password to ciscolab

How to reset Cisco router password?

Either switch off or shut down the router.

Remove the compact flash that is on the rear of the router.

Switch on the router.

Once the router is on Rommon mode,reinsert the compact flash.

Type confreg 0x2142 at the rommon 1> prompt in order to boot from Flash.

Type reset at the rommon 2> prompt.