What is Session target in dial peer?
What is Session target in dial peer?
The session target distinguishes one session from the other. In dial-peer 999, the IP address of the server is provided as the session target. The address can be the address of a UA, proxy server, or redirect server. In dial-peer 200, the session target is the sip-server parameter.
What does dial peer mean?
A dial peer, also known as an addressable call endpoint, is a device that can originate or receive a call in a telephone network. In voice over IP (VoIP), addressable call endpoints can be categorized as either voice-network dial peers or POTS (plain old telephone service) dial peers.
How do I check my dial peer status?
You can test your dial-peer with the command show dialplan number xxxphone numberxxx. If the call is active you can check used dial-peer with the command show voice call status. Regard.
What does default dial peer mean?
Dial-peer 0 (pid:0) has a default configuration that cannot be changed. The default dial-peer 0 fails to negotiate non-default capabilities, services, and applications such as: Non-default Voice-Network capabilities: dtmf-relay, no vad, and so forth.
How does dial peer work?
Another command used with dial peers is destination-pattern. The destination pattern is used to associate a dial string with a particular telephony device. The call is routed when a dialed string matches a destination pattern. The POTS or VoIP voice port configuration determines the way the call is routed.
What is destination pattern 9T?
The router pauses to collect additional dialed digits. For example destination-pattern 9T matches the digit 9 followed by zero or more digits- it will route the call only after the expiry of the inter-digit timeout.
Why is dial peer used?
Dial peers are used to identify call source and destination endpoints and to define the characteristics applied to each call leg in the call connection. A traditional voice call over the public switched telephone network (PSTN) uses a dedicated 64K circuit end to end.
What is dial plan in VoIP?
A VoIP dial plan is the path an inbound call will take through your phone system. A dial plan is usually mapped out online using a dial plan editor on your VoIP service provider’s portal. Dial plans go by many names: call tree, call path, call flow, and call route to name a few.
What is inbound dial peer?
–> Outbound dial peers are used for outgoing VoIP calls whereas Inbound dial peers are used for Incoming VoIP calls on Voice Gateway.
What happens if there is no matching dial peer for an outbound call?
If no incoming dial peer matches the calling number, the inbound call leg automatically matches to a default dial peer (POTS or VoIP).
What are dial peers Cisco?
Dial peers identify call source and destination endpoints and define the characteristics that are applied to each call leg in a call connection. Understanding the principles behind dial peers can increase your understanding of how Cisco IPICS works.
Why is dial-peer used?
How does dial-peer work?
What is inbound dial-peer?
What is default dial-peer in Cisco?
If a match is not found in the previous steps, then the default is dial peer 0. Because call setups always include DNIS information, it is recommended that you use the incoming called-number command for inbound dial-peer matching.
How does dial plan work?
A dial plan (or dialing plan) establishes the permitted sequences of digits dialed on subscriber lines or on subscriber premises equipment, such as telephones and private branch exchange (PBX) systems.
What is SIP UA Cisco?
You can enable Session Initiation Protocol (SIP) UA commands, using the ios-voice:sip-ua configuration mode. The ios-voice:sip-ua mode is a part of Cisco-IOS-XE-voice module. The following operations are allowed in the ios-voice:sip-ua mode: Operations.
How do I create a dial plan?
How do I create a dial plan?
- Select Dial Plans in the left sidebar and then select Add Dial Plan.
- The next available number will automatically populate the Extension; change this number as needed.
- Enter a Name for the dial plan.
- and then select the new dial plan to open the editor.
What is a SIP user agent?
A SIP user agent (UA) is an endpoint device that supports SIP. SIP is used to establish connections and enable sessions between SIP UAs. A UA acts on behalf of a user, usually a person but can be another protocol. A UA comprises both client (UAC) and server (AS) applications.
What is a Cisco cube?
Cisco Unified Border Element (CUBE) is a unified communications border element, providing voice and video connectivity between the enterprise IP network and service provider network. It is similar to a voice gateway, except for the replacement of physical voice trunks with an IP connection.
