What is the underside of a roof called?

soffit
Your roof by necessity, will often times extend over the walls of your home. This overhang can go by a few names, such as the house eaves or the rafters of your roof. The underside of this overhang, when given a finished appearance, is known as the soffit, which means “something fixed underneath”.

What is a draw in roofing?

Roof Tools Draw Roof is for drawing Gabled, Hipped, Saltbox, Shed and Sloped roof styles with a few mouse-clicks. Adjust peak, hip, overhang, and more.

What is the area under the eaves of a house called?

Eave – The overhanging area of the roof that extends beyond the house to keep rain water away from the lower part of the home. Soffit – Covering for the underside of the eave, often vented.

What is the eaves of a roof?

The area where a roof extends a small way past the wall of a building is usually referred to as the eaves. This is an essential part of the roofing as this area has to be finished properly to prevent animals nesting and potential water ingress.

What is under the soffit?

What is Fascia? If ‘soffit’ is the horizontal base area that covers the eaves, ‘fascia’ is the vertical. Fascia board is placed on the ends of the eave rafters and under the roof shingle or tile.

What is board under soffit called?

Frieze boards are horizontal trim members you see at the top of your siding right where it meets the eave or soffit line. Frieze boards sit flush against your wall but jut out enough for your siding to tuck under.

What type of drawing is a roof plan?

A roof plan will usually just be a 2-dimensional drawing that depicts your roof from a bird’s eye view. The plan is written to coincide with the scale of your home’s floor plan. It will often include notes that detail specifics about the pitch of the roof, as well as its ridges and slopes.

What is a soffit vs eave?

Eaves and soffits are often composed of different materials. Eaves are usually made of wood and then covered with roofing material. Soffit materials coordinate with siding and fascia boards on the exterior walls, and generally follow the aesthetics of the residence.

What are the roof parts called?

Ridge: This is the top or peak of the roof, where two roof planes meet. Valley: This is where two pitched roof faces connect and project inward. They are always at a lower slope than the adjoining roof planes. Dormer: This is a roof feature that projects out from the roof face.

What are eaves and fascia?

Eaves—The lower edge of a roof (often overhanging beyond the edge of the house). Fascia—A decorative board extending down from the roof edge either at the eave or at the rake. Felt—The bituminous paper used by roofers, usually made of a combination of asphalt and either paper or rags.

What is the wood under the eaves called?

Soffit: The underside of the eaves, or roof overhang, which can be enclosed or exposed. Soffit Vent: An intake vent in the soffit area of the house that provides attic venting at a lower portion of the roof deck and good circulation with other forms of venting such as ridge or roof vents; also called an intake vent.

What is the piece under the gutter called?

The soffit is a horizontal piece of material that meets the end of the fascia and connects to your house. Soffit is French for an item that is positioned underneath something else. In this case, the soffit goes underneath the fascia.

What is the board at the bottom of siding called?

Buttlock. The bottom portion of a panel of vinyl siding that locks into a previous panel that was just installed. This keeps the siding from moving around.

What is elevation drawing?

An elevation drawing is an orthographic projection drawing that shows one side of the house. The purpose of an elevation drawing is to show the finished appearance of a given side of the house and furnish vertical height dimensions. Four elevations are customarily drawn, one for each side of the house.

What is the difference between fascia and eaves?

What is fascia trim?

Fascia is a specific type of trim, which is installed just below the roof line. It helps to cover the soffit, and provides a more finished appearance for the roof and eaves of the home. These boards may vary in width, but is generally a slightly wider or thicker version of the same trim used on the rest of the home.

What are 5 parts of the roof frame?

The Five Components of a Roofing System In sloped roofing structures there are five basic components that need to come together to allow the roof to do its job and protect the home from the elements. These five components include the roof covering, sheathing, roof structure, flashing and drainage.

How do I draw a roof?

Use the following steps to draw a roof: Create a structure to put the roof on. Choose Build>Draw Roof. Cursor changes to a transparent disc to gauge drawing height Position disc on wall top before drawing. Click-and-drag from one corner of the wall top to the other. In wireframe, drag blue handles to outer wall edges to snap in place.

What is roofing underlayment?

Roofing Underlayment: Roofing underlayment is a layer of material, usually synthetic or felt, that adds extra protection on top of the roof deck and under the shingles. Synthetic underlayment helps repel moisture and provides protection against water infiltration.

What is the flashing on a roof called?

You may recognize flashing as metal stair steps alongside a chimney or side walls on a roof. Hip: The hip on a roof is the intersection of two roof planes that meet to form a sloping ridge running from the peak to the eave.

How do I hide a roof in Revit?

Right-click a roof and choose Hide from the pop-up menu. In wireframe the whole roof is hidden. In finished mode only the roof half you right-click will be hidden. Hide All Roofs by choosing View>Hide>Roofs or press the R key.